TapMaster
|
TapMaster is an
assembly of two basic components - the valve
block that connects in-line to the hot and/or
cold water lines and the pilot/actuator valve
that activates the unit. A standard TapMaster
consists of two valve blocks one for each hot
and cold water line and one pilot/actuator valve
that may use a cabinet door or foot activator.
The versatility and adaptability of this
component design allows for a variety of
configuration to suit virtually any faucet/sink
arrangement.
No electrical,
no batteries, no electronics. TapMaster operates
using water pressure in existing water lines.
Installation hardware and detailed instructions
included.
5 year limited warranty |
Hands - Free Faucet
Controller
-
Add-on for conventional
water faucets where flow rate & temperature are
pre-set on faucet.
-
Can be used with
intermittent on-off or continuous-on without constant
foot pressure.
-
Activator requires 4
inch toe-kick under sink cabinet
-
Hands free operation
reduces cross-contamination
-
Installation kit is
complete & has excellent instructions.
-
86% of 14 CRA Evaluators
stated this product would replace products they use
currently, & 93% rated it excellent or good; worthy of
trial by colleagues (CRA news letter volume 26, issue
2, February 2002, Page 4)
-
Works on water pressure
alone-no power outlets , batteries or compressed air
required
-
Hands free continuous
flow for kick pedal models only
-
Plated solid brass valve
blocks
-
High pressure control
tubing with protective sheath
-
Built-in protection for
water borne debris
-
Completely assembled
-
Installation hardware
and instructions included
Foot Activated Models
Kick plate models mount
on cabinet toe kicks. Set faucet open at the flow and
temperature desired; press foot lightly against vertical
face of the kick plate to activate water flow and
release to stop it. For continuous flow press down on
the angled face to latch; to release press the vertical
face. Kick plate is made from 18 gauge stainless steel.
|
Item # |
Description |
Price |
|
1740 |
Kick Plate
Activation for single water line |
$247.00 |
|
1742 |
Dual Kick
Plates for single water line |
$395.00 |
|
1750 |
Standard
Kick Plate Activation for hot and cold water
lines |
$345.00 |
|
1752 |
Dual Kick
Plate Activated for Island Cabinet |
$498.00 |
Euro
Foot Activated Models
Euro models mount on
cabinet toe kicks. Set Faucet open at the flow and
temperature desired; push Euro foot activator in any
direction for momentary water flow, release to turn off.
For continuous water flow, push Euro foot activator
sideways to 45 degrees in either direction to lock on;
push activator back to vertical rest position to turn
off. Finishes available: Chrome or Brushed Nickel.
|
Item # |
Description |
Price |
|
1770 |
Euro style
with Momentary Actuator - for hot & cold water
lines |
$325.00 |
|
1771 |
Euro Style
with Momentary Actuator - Single Water line |
$229.00 |
|
1775 |
Euro Style
with locking actuator - hot and cold water lines |
$345.00 |
|
1776 |
Euro Style
with locking Actuator - Single Water line |
$249.00 |
Cabinet Door Models
These models utilize the cabinet door as the activator
by pressing the
button valve mounted on the inside
cabinet wall opposite the door hinge.
Set the faucet open at the flow and temperature desired; press knee
lightly against
the cabinet door to activate water flow
and release to stop it.
|
Item # |
Description |
Price |
|
1710 |
Cabinet
door activation for single water line |
$206.00 |
|
1720 |
Standard
Cabinet Door Activation |
$302.00 |
|
1722 |
Dual Door
Activation for Island Cabinet |
$409.00 |
Floor Foot Pedal Models
Floor foot pedal models
are designed for a variety of applications including
wall mounted sinks, sinks in cabinets with or without
toe kicks, or any non typical sink arrangements. Floor
foot pedals are made from 18 gauge stainless steel and
are operated either from the floor or mounted on a
vertical face and used as a kick plate.
|
Item # |
Description |
Price |
|
1760 |
Floor Foot
Pedal |
$345.00 |
|
1762 |
Dual Floor
Foot Pedal for island cabinet |
$498.00 |
Combination Kick Plate & Door Activation Model
The model 1751 offers
you the best of both worlds. It is a combination of the
models 1750/1720 and is used in cabinet or island
situations. Set the faucet open at the flow and
temperature desired: press your foot against a kick
plate or your knee against the cabinet door to activate
water flow and release it to stop. Kick plate is made
from 18 gauge stainless steel.
|
Item # |
Description |
Price |
|
1751 |
Combination
Kick plate & door activation |
$477.00 |
SPECIFICATIONS
|
Dimensions: |
Valve Block
(less tubing fittings) |
2.26" x .88" x 1.25" (5.74 x 2.24 x 3.18cm) |
| Button Valve
(less fittings) |
.63" x .63" x 1.0" (1.60 x 1.60 x 2.54cm) |
| Kick Plate
(1750, 1752, 1740, 1742) |
8.0"w x 3.42"h, 1.14"d (20.32 x 8.64 x 2.90cm) |
| Floor Foot
Pedal (1760, 1762) |
7.1"w x 3.0"h x 1.1"d (18 x 7.6 x 2.8 cm) |
| Euro Foot
Activated |
|
| (1770, 1771,
1775, 1776) |
1.19"w x 4.92"h x 1.37"d (30 x 125 x 35mm) |
|
Pressure: |
Operating |
0
to 100 psi (690 kpa) maximum |
| Static Burst
Rating |
700 psi (4,830 kpa) for complete assembly |
| Flow: |
Both Valve
Blocks |
7.2 gpm @ 60 psi (27.0 l/m @ 4 bar) |
|
Construction: |
Valve Bodies |
Chrome Plated Brass |
| Seals |
Silicone or E.P.D.M. |
| Control Tubing |
1/8 O.D. 3 tube bundle (high density
polyurethane) |
| Kick Plate |
18g #4 stainless steel top, aluminum base |
| Euro Foot
Activated |
Housing - chrome or nickel plated brass housing;
cap - chrome or nickel plated brass; |
| |
Foot Probe - polyurethane |
|
Filtration: |
Control
Circuit |
25
micron |
| Main Port |
greater than .060" (1.5mm) |
Connections
Valve Blocks |
Inlet |
3/8" tube (for 3/8" compression) |
| Outlet |
Nut and sleeve, 3/8" compression |
Installation
Requirements: |
Cabinet Door
(1710, 1720, 1722) |
Cabinet door of suitable height and construction
for knee pressure, spring loaded hinges
recommended. |
Kick Plate
(1750, 1752, 1740, 1742) |
Toe kick height of not less than 4" (10.2cm)
horizontal clearance of at least 8" (20.4 cm) on
one end of plate to allow for removal of
stainles steel cover |
Euro Foot
Activated
(1770, 1771, 1775, 1776) |
Toe kick height between 3" to 6" (75 to 150mm)
polyurethane probe can be cut to length to fit
by keeping the bottom of the probe between 1/2
to 1" above the finished floor. |
|
